Haier Error Codes, Indoor Codes and Outdoor LED Flashes
Haier error codes come in two flavours.
Indoor faults appear as E codes on the indoor display, while outdoor faults are coded F and counted out by flashes of an LED on the outdoor board. Knowing which is which tells you where the problem lives before anyone opens a panel. Below, you will find the codes from the Haier service manual for Australian wall splits, sorted by where they point, with a detailed page behind each one.
Where do Haier error codes come from?
The codes on this site come from the Haier service manual for Australian wall split models, published on the Haier Australia website. The same code set appears in Haier service manuals for several overseas ranges, which helps confirm the meanings.
Think of each code as a signpost. It sends you toward a sensor, a fan, a circuit board, the gas charge or the electricity supply, so nobody wastes time hunting blindly.
How do Haier units show a fault?
According to Haier service documentation, codes display on the indoor unit panel in place of the set temperature. So when a number is replaced by letters such as E7, the unit is reporting a fault.
For outdoor faults, the outdoor control board also flashes an indicator, LED1, a set number of times. Technicians read that flash count during diagnosis.
What is the difference between E and F codes?
In practical terms, the letter tells you which half of the system to look at. Codes starting with E concern the wall unit inside and the cable conversation between the halves. Codes starting with F concern the box outside, including its sensors, electronics, compressor, gas charge and power.
So an E code usually means a technician working in your room, while an F code usually means work out by the condenser.
Which E codes relate to the indoor unit?
The indoor codes in the Haier manual are these.
- E1 is a room temperature sensor failure.
- E2 is a heat exchange sensor failure on the indoor coil.
- E4 is an indoor EEPROM error.
- E14 is an indoor fan motor malfunction.
Sensor faults are usually the cheapest to fix. Fan and board faults cost more.
Which code relates to the link between units?
E7 flags lost contact between inside and outside. On the outdoor board, LED1 flashes 15 times for it.
Most often, a slack terminal, a damaged or badly joined cable or a wiring mix up is to blame, while failed boards are a smaller share.
Which F codes relate to outdoor sensors?
Haier fits a handful of thermistors outside, and the manual gives every one its own code and flash count.
- F6, 12 flashes, is the ambient temperature sensor.
- F7, 11 flashes, is the suction temperature sensor.
- F21, 10 flashes, is the defrost temperature sensor.
- F25, 13 flashes, is the discharge temperature sensor.
Outdoor sensors wear faster than indoor ones because of weather, salt and pests.
Which F codes relate to outdoor electronics?
These codes point to the outdoor board and power module.
- F12, 1 flash, is an outdoor EEPROM error.
- F1, 2 flashes, is IPM protection.
- F3, 4 flashes, is a communication fault between the IPM and the outdoor board.
- F19, 6 flashes, is supply voltage too high or too low.
- F22, 3 flashes, is AC overcurrent protection.
Supply problems and heat often sit behind these, so the technician checks both.
Which F codes relate to the compressor?
Several codes describe how the compressor is running.
- F2, 24 flashes, is compressor overcurrent.
- F4, 8 flashes, is discharge temperature overheat protection.
- F28, 19 flashes, is a compressor position detection or synchronism error.
- F20, 5 flashes, is compressor overload.
- F27, 7 flashes, is a blocked compressor.
- F11, 18 flashes, is the compressor operating outside its normal range.
These codes deserve prompt attention, since the compressor is the dearest part of the system.
Which codes relate to refrigerant and the valve?
- F13, 16 flashes, is insufficient gas.
- F14, 17 flashes, is a four way valve fault.
- F30, 14 flashes, is compressor suction temperature too high.
A low charge always means a leak somewhere, which should be found and repaired.
Which code covers the outdoor fan?
F8, 9 flashes, is an outdoor DC fan motor fault. Debris, worn bearings, a failed motor or a board fault can all cause it.
What should you do when a code appears?
First, capture it. Snap a picture of the panel and jot down whether the unit was heating or cooling, the time and the weather. Afterwards, find the code in the lists above and open its page.
Every code page covers the likely causes, the checks you can safely make and the point at which a technician is needed.
Should you restart the system?
A single power cycle is a sensible first move for most codes. Use the handset to switch off, drop the breaker for five minutes or more and then try again. Our restart guide walks through it.
However, codes that involve the compressor, the gas charge or high current deserve restraint. Repeated attempts load expensive parts each time.
Why read the code before switching off?
Some faults are intermittent. If you switch off before noting the code, you may lose the clue until the fault happens again. A quick photo of the display solves that.
Our guide to reading Haier codes has more tips.
Can the same symptom have different codes?
Yes. For example, poor cooling might come with F13 for low gas, F4 for overheating, F8 for the outdoor fan or no code at all. The code narrows the search, while the technician confirms the cause with tests.
Can several codes appear together?
Indeed they can. A shaky supply might throw F19 one day, F22 the next and E7 later in the week. Similarly, an ageing outdoor board might alternate between F12 and F3. Keeping a dated list lets the technician spot the thread running through them.
Are these codes the same as other brands?
Not at all. Each manufacturer writes its own list, and identical characters can describe completely different faults from one badge to the next. Check that any advice you read is written for Haier wall splits before acting on it.
How do our technicians use the codes?
For our team, the code opens the investigation rather than closing it. They verify it, count the outdoor LED flashes where relevant and then measure the components involved. Just as importantly, they hunt for the reason behind the fault, whether that is water creeping onto a sensor or a matted coil starving the system of air.
What does it cost to fix a Haier code?
Prices follow the cause. Sensors and loose connections are the cheaper fixes. Fan motors, reversing valves and circuit boards sit further up the scale. Gas leaks and compressors cost the most.
You receive a firm quote after testing, and our price guide shows how it is built.
Why does Haier use outdoor LED flash counts?
The outdoor unit has no display of its own, so the board signals faults by flashing an LED. Each fault has its own count, from a single flash for the memory error to twenty five for single phase compressor overcurrent. Consequently, a technician can identify an outdoor fault within seconds of removing the cover.
You do not need to read the LED yourself. The indoor display, and the technician on site, handle that.
Which codes are most common in Sydney?
In our experience, the codes we meet most on Haier wall splits are E7 for communication, E1 and E2 for indoor sensors, outdoor sensor codes such as F21, and protection codes such as F1, F4 and F19 during hot weather.
Meanwhile, coastal homes show more sensor and connection faults, and western homes show more overheating and overcurrent in summer.
Which codes need the fastest response?
Codes linked to the compressor, the gas charge or high current, such as F1, F2, F4, F13, F22 and F28, protect the most expensive parts. Therefore, book promptly and avoid repeated restarts.
By contrast, sensor codes such as E1 or F6 rarely cause further damage while the system is off, though the system will not run until they are fixed.
Can a code appear with no real fault?
Occasionally. For instance, a brief power dip during a storm can corrupt a memory read and show E4 or F12 once. A careful restart often clears that kind of glitch. If the code returns, however, it is real.
What if there is no code at all?
Many problems never show a code, at least at first. Weak cooling, a musty smell, drips or new noises often appear before any code. Our problems page covers those symptoms.
Do ducted Haier systems use the same codes?
Haier ducted and cassette systems use their own controllers, and codes may differ from the wall split list here. If you have a ducted system, note whatever the controller shows and call us. Our ducted page explains how we help.
How can you prevent common codes?
Simple habits help. First, wash the filters every few weeks in busy seasons. Next, keep the outdoor unit clear and well ventilated. In addition, turn the system off during severe storms and book a yearly service. Together, those steps prevent many of the faults behind common codes.
Why do outdoor codes cluster in summer?
Summer pushes outdoor units hardest. Pressures rise, compressors run longer and network voltage dips during peak demand. As a result, protection codes such as F1, F2, F4, F19 and F22 appear more often from December to March.
A pre summer service, with a coil clean and connection check, reduces the odds noticeably.
Why do some codes appear in winter?
In winter, reverse cycle systems run long heating sessions and defrost on cold mornings. Outdoor sensor codes, particularly F21 for the defrost sensor, and reversing valve faults such as F14 tend to surface then.
Heating that pauses with a defrost icon is normal, though, so not every pause means a fault.
Which models does this list cover?
The Haier manual we used covers Australian wall split models such as 1U71SABFRA and lists other Haier outdoor units, including 1U53RABFRA and several 1U JACFRA and BYFSRA models. The same codes appear across Haier service manuals for other wall split ranges.
If your model is not mentioned, the codes are still very likely to apply, but our models page explains how to check.
What should you avoid doing?
Do not open the outdoor unit to count flashes yourself. The control box holds high voltage, and the Haier manual tells technicians to wait at least five minutes after unplugging before touching the board. Leave that part to us.
Do multi splits show codes differently?
On a multi split, each indoor unit has its own display, so an indoor fault usually shows only in one room. An outdoor fault, by contrast, can stop every room and may show on several indoor units at once. Noting which rooms show a code tells the technician where to start.
How do you book a Haier repair?
Call 02 9071 1142 or send a request from our booking page. Share the code, the model numbers on the rating labels and what you noticed when it stopped.
Our technicians cover Sydney widely, as the areas page shows. A clean coil and fan barrel improve comfort as well as efficiency. Summer and winter both bring their own kinds of air conditioner faults. Older systems can often be kept running well with the right care.
Frequently asked questions
Where do Haier error codes appear?
Indoor codes show on the indoor display in place of the set temperature. Outdoor faults also flash an LED on the outdoor board.
How do E and F codes differ?
E points inside and to the cable link, while F points to the outdoor box and its parts.
What does E7 mean?
It is a communication fault between the indoor and outdoor units.
What does F13 mean?
It means insufficient gas, which usually points to a leak.
Is a restart a good idea?
Once, yes. Hold back on repeats for compressor, gas or current codes.
How can I arrange a visit?
Call 02 9071 1142 and share the code and the model labels.